Trystan Casey
If your General Electric (GE) dishwasher isn't draining, there are several steps you can take to identify and fix the problem. A common issue is a clogged drain hose, which can be cleared by removing and flexing the hose or blowing through it to dislodge any blockages. You should also check the sink drain and garbage disposal for clogs, and ensure that the drain hose is properly elevated and connected. If these steps don't resolve the issue, you may need to check the filter, drain valve, solenoid, motor, and pump for any blockages or malfunctions. In some cases, a failing motor or electrical problem could be the cause. If you're unable to identify the issue, it's recommended to consult a professional appliance repair technician for further assistance.
Characteristics and Values Table for Draining a General Electric Dishwasher
| Characteristics | Values |
|---|---|
| Excess water in the dishwasher | Check for blockages or kinks in the drain hose |
| Remove and check filters at the bottom of the dishwasher | |
| Make sure the kitchen sink drain is not clogged | |
| If a disposer is installed, run it to clear the drain system | |
| Remove the cap on the air gap and clean out any debris | |
| Do not use drain cleaner in the dishwasher | |
| Do not use too much detergent to avoid over-sudsing | |
| Make sure the height of the drain hose matches the installation instructions | |
| If the dishwasher is jammed, check the drain pump and blow through the hose to check for clogs | |
| If the above solutions do not work, service will be needed |
Explore related products
What You'll Learn
Check for blockages in the drain hose
If your General Electric dishwasher is not draining properly, the drain hose is one of the first things you should check for blockages. The drain hose connects the dishwasher to your garbage disposal or sink and is usually located under the sink or behind the dishwasher.
To check for blockages in the drain hose, first, locate the hose. If it is a new dishwasher, the drain hose will be white and corrugated. If you are having trouble locating the hose, measure the height from the floor to the highest point of the drain hose and refer to the Installation Instructions for your dishwasher.
Once you have located the hose, check to see if it is properly secured to the sink or garbage disposal. If it is not properly connected, food or debris may be the cause of the blockage. You can clean your drain hose using a drain cleaner solution or a natural solution of baking soda and vinegar.
If the hose is properly connected and there is no visible blockage, you can try blowing through the hose to see if it is clogged. Alternatively, if you have a compressor, you can try blowing some of the lines out. If the hose is blocked, you may need to remove it and flex it to clear the blockage, or use a garden hose to clear it out.
If you are unable to clear the blockage in the drain hose, you may need to replace the hose or call a service technician.
Where is the Reset Button on an Electric Fireplace?
You may want to see also
Explore related products
Clean the filter
If your General Electric (GE) dishwasher is not draining properly, there are a few things you can do to fix this. Firstly, check for any large pieces of food at the bottom of the dishwasher and remove them. Next, check the drain hose for any blockages or kinks. If you are unable to locate the blockage, you will need to go from the drain hose backwards. You can remove the kickplate below the door to gain access to the drain pump. The drain hose can be removed and you can blow through it to check for any blockages.
If your dishwasher has a Fine and Ultra Fine filter, you will need to clean them periodically. First, remove the bottom rack and then the Ultra Fine Filter by twisting it counterclockwise and lifting it. Rinse the filter with warm soapy water and use a sponge to remove any stubborn particles. Reinsert the filter and twist it clockwise to lock it into place.
Next, remove the Fine Filter by twisting the two retaining posts at the back, bottom of the dishwasher tub counterclockwise. Rinse the Fine Filter with warm soapy water and use a sponge or soft brush to remove any stubborn soils or calcium deposits. Reinsert the Fine Filter and twist the retaining posts clockwise to lock them into place.
If your dishwasher does not have removable filters, you can try a white vinegar cycle followed by a tub clean with Affresh, and finally an empty cycle to rinse the unit out.
Fixing a Squeaky Electric Fireplace: A Step-by-Step Guide
You may want to see also
Explore related products
![[Upgraded] 2Pcs WD12X10426 Dishwasher Upper Dishrack Slide Rail Stop, Dishwasher End Cap fit for GE Hotpoint Dishwasher, Replaces AP5688593, PS7783360](https://m.media-amazon.com/images/I/51MVTzlH3TL._AC_UY218_.jpg)
Remove large objects from the sump area
If your General Electric dishwasher is not draining, there are a few things you can do to fix the problem. First, check for any large objects that might be blocking the sump area at the rear of the tub. Remove any large pieces of food, such as noodles, lettuce, or bones, from the bottom of the dishwasher.
Next, you can check the drain hose for any blockages or kinks. Remove the kickplate below the door to access the drain pump, which is connected to the right side of the center sump. Check the hose for any signs of clogging, and if necessary, remove and flex the hose to clear any blockages. You can also try blowing through the hose to check for blockages.
If your dishwasher has a garbage disposal, make sure to run it to clear the drain system before running the dishwasher. It is also important to ensure that the kitchen sink drain is not clogged.
By following these steps, you can effectively remove large objects from the sump area and troubleshoot common drainage issues with your General Electric dishwasher.
Electric Gate Installation: A DIY Guide
You may want to see also
Explore related products
Check the height of the drain hose
If your General Electric dishwasher is not draining properly, there could be a problem with the height of the drain hose. The first step is to locate the drain hose. The drain hose is usually found below the sink and connects the dishwasher to the sink. Once you have located the hose, check for any blockages or kinks in the hose. If there are any large pieces of food or debris in the hose, clear them out.
After clearing any blockages, you should measure the height of the drain hose to ensure it is installed at the correct height. Measure the height from the floor to the highest point of the drain hose. Refer to the Installation Instructions for your dishwasher model to determine the correct height. The Installation Instructions will specify the required height of the high drain loop in relation to the underside of the counter and the sink.
If the height of the drain hose does not match the specifications in the Installation Instructions, adjustments may be necessary. Ensure that the high drain loop is attached securely to the underside of the counter and connected to the sink at the specified height.
It is important to note that reusing old or worn-out drain hoses is not recommended as they may be more prone to kinking or blockages. Always use the new white corrugated drain hose that comes with your dishwasher. By checking the height of the drain hose and ensuring it meets the installation requirements, you can help ensure proper drainage of your General Electric dishwasher.
Microphones: Electricity to Sound Conversion Explained
You may want to see also
Explore related products
Check the drain pump
If your General Electric (GE) dishwasher is not draining properly, you should check the drain pump for any obstructions. First, disconnect your appliance from its power source. You will likely find the pump behind the lower access panel. If you are having trouble locating it, refer to your dishwasher's manual or search for your model online.
Once you have located the pump, check for any debris or dirt that may be causing a blockage. If you notice any obstructions, carefully remove them. If your GE dishwasher uses a check valve as part of the drain pump, you should also inspect the piston and nut assembly. The assembly should move up and down freely, and the piston should form a tight seal when in the down position. If the piston and nut assembly is not functioning properly, you will need to replace it.
If there are no visible obstructions to the drain pump, you can try removing the hose casing from the pump motor and cleaning the motor around the propeller. After cleaning, lubricate the motor and turn the propeller manually a few times to dislodge anything that may be jamming it. If the propeller is still not turning, something may be stopping it from rotating.
You can also test the pump using a multimeter. First, ensure that your appliance is disconnected from the power source and locate and remove the pump. Then, using a multimeter on Rx1 mode, touch the pump's terminals with the probes. You are testing for continuity and should receive a reading of zero or close to zero. Next, test the ground connection by touching one of the probes to the bare metal housing while leaving the other on a terminal. If the results of these tests are not as described, you will need to replace the pump.
Fixing Your Electric Lawn Mower: A Step-by-Step Guide
You may want to see also
Frequently asked questions
You will typically see an excess amount of water in the bottom of the tub.
There could be a blockage or a kink in the drain hose, or the hose could be clogged. The kitchen sink drain might be blocked, or there could be a problem with the disposer.
Make sure the drain plug inside the disposer was removed. Always turn on your garbage disposer before running the dishwasher to clear out any debris or food within the drain system.
Check that the height of the drain hose matches the Installation Instructions for the dishwasher. You can also blow through the drain hose to see if it is clogged.
Start a cycle and press cancel one or two times after the cycle has started. This will put the dishwasher into a two-minute drain.
