
Electric start dirt bikes are a convenient alternative to kick-starting your bike. They are easy to use, with a simple push-button start, and can be added to your bike by swapping motors. However, some riders prefer to learn to kick-start their bikes as part of the experience of learning to ride. In this article, we will explore the steps to electric-starting your dirt bike and the pros and cons of this method.
Characteristics | Values |
---|---|
Step 1 | Turn the key in the ignition to the "ON" position |
Step 2 | Locate the electric start button on the handlebar controls |
Step 3 | Ensure the bike is in neutral and the kill switch is in the "RUN" position |
Step 4 | Press and hold the electric start button until the engine turns over and starts |
Note | If the engine does not start after a few seconds, release the button and wait a few moments before trying again |
Note | Make sure the battery is fully charged to ensure reliable starting |
Other ways to start a dirt bike | Kick start |
Electric start motors | YX 140cc electric start |
What You'll Learn
Turn the key in the ignition to the ON position
To start a dirt bike with electric start, the first step is to turn the key in the ignition to the "ON" position. This is a simple step, but it is important to ensure that this is done correctly before proceeding with the next steps. Once the key is in the "ON" position, you can locate the electric start button on the handlebar controls. It is important to make sure that the bike is in neutral and the kill switch is in the "RUN" position before proceeding.
Turning the key in the ignition to the "ON" position is a crucial step in starting a dirt bike with electric start. This step ensures that the bike's electrical system is activated and ready to receive the signal from the electric start button. Without this step, the bike will not be able to start. It is also important to note that the key must be turned to the "ON" position before pressing the electric start button. Attempting to start the bike with the key in the "OFF" position may damage the electrical system or the starter motor.
Additionally, when turning the key to the "ON" position, it is important to ensure that the bike is in neutral. This will allow the bike to start without any resistance from the transmission. If the bike is in gear when the electric start button is pressed, it may lurch forward unexpectedly. Therefore, it is crucial to confirm that the bike is in neutral before proceeding.
Furthermore, it is worth noting that some dirt bikes may have a kill switch, which is a safety feature that can cut power to the engine in the event of an emergency. To start the bike, the kill switch must be in the "RUN" position. This allows the engine to receive power from the electrical system. If the kill switch is in the "OFF" position, the bike will not start even if the key is turned to the "ON" position and the electric start button is pressed.
In summary, turning the key in the ignition to the "ON" position is a critical step in starting a dirt bike with electric start. It ensures that the bike's electrical system is activated and ready to receive the signal from the electric start button. By following this step correctly, you can avoid potential damage to the electrical system or starter motor and ensure a smooth and safe starting process.
Determining Electric Bike Distance: Factors and Calculations
You may want to see also
Locate the electric start button
To locate the electric start button on a dirt bike, first turn the key in the ignition to the "ON" position. The electric start button should be located on the handlebar controls. It will be a push-button starter, similar to those on street bikes. Once you have located the button, ensure the bike is in neutral and the kill switch is in the "RUN" position. You can then press and hold the electric start button until the engine turns over and starts. If the engine does not start after a few seconds, release the button and wait a few moments before trying again. Make sure the battery is fully charged to ensure reliable starting.
Unleashing Your Bosch Electric Bike: Removing Restrictions
You may want to see also
Ensure the bike is in neutral and the kill switch is in the RUN position
To start an electric dirt bike, you must first ensure the bike is in neutral and the kill switch is in the RUN position. This is a crucial step and must be done before you attempt to start the engine. The kill switch is usually located on the right handlebar, and you should be able to see a clear 'RUN' position.
Next, you need to locate the electric start button. This is usually found on the handlebar controls. Once you have located the button, you can press and hold it to start the engine.
It is important to note that if the engine does not start after a few seconds, you should release the button and wait a few moments before trying again. A common issue is that the battery is not fully charged, so ensure this is the case before attempting to start the bike.
Some electric dirt bikes also have a kickstand, which can be used to start the bike if the electric start is not functioning.
Concealing Your Electric Bike: Creative Disguise Techniques
You may want to see also
Press and hold the electric start button
To start a dirt bike with electric start, you must first turn the key in the ignition to the "ON" position. Then, locate the electric start button on the handlebar controls. Ensure the bike is in neutral and the kill switch is in the "RUN" position. Now, press and hold the electric start button until the engine turns over and starts. If the engine does not start after a few seconds, release the button and wait a few moments before trying again. Make sure the battery is fully charged to ensure reliable starting.
Unleashing Electric Bike Potential: Derestricting for Performance
You may want to see also
If the engine doesn't start, release the button and wait a few moments before trying again
To start a dirt bike with an electric start, first turn the key in the ignition to the "ON" position. Then, locate the electric start button on the handlebar controls. Ensure the bike is in neutral and the kill switch is in the "RUN" position. Press and hold the electric start button until the engine turns over and starts. If the engine doesn't start after a few seconds, release the button and wait a few moments before trying again. Make sure the battery is fully charged to ensure reliable starting.
Electric push-button starters are a convenient feature of modern dirt bikes, similar to those found on street bikes. They offer a quick and easy way to start your bike with the push of a button, eliminating the need for a kick start. However, it's important to remember that if the engine doesn't start right away, releasing the button and waiting briefly before trying again can help prevent any potential issues.
Building an Electric Bike: A Step-by-Step Guide
You may want to see also
Frequently asked questions
To start a dirt bike with an electric start, turn the key in the ignition to the "ON" position, locate the electric start button on the handlebar controls, ensure the bike is in neutral and the kill switch is in the "RUN" position, then press and hold the electric start button until the engine turns over and starts.
If the engine doesn't start after a few seconds, release the button and wait a few moments before trying again. Make sure the battery is fully charged to ensure reliable starting.
Yes, you can add an electric start to your dirt bike by swapping motors. You can buy a YX 140cc electric start motor for 400 to 600 and sell your old motor to recoup some of the cost.
No, not all dirt bikes have electric start. Some have kick and electric start, and some have kick start only.
Yes, you can start your dirt bike with the kickstand down.