
Installing new grips on your Electra bike can be a simple process, but it's important to take your time and follow the directions carefully. The first step is to remove the screws on the switch housing and separate it, cutting off the left side grip if necessary. You'll then need to add adhesive to the leading edge of the new grip, position it as desired, and slide it on. It's also crucial to shim the brake handle out to avoid damaging the brake switch when removing the switch housing. Once everything is tightened, ensure that the wires are not pinched.
Characteristics | Values |
---|---|
Installation process | Remove screws on the switch housing, separate the housing, remove the stock grip, add adhesive to the leading edge of the new grip, position and orientate the grip, slide it on, and tighten everything up |
Additional notes | Ensure the wires are not pinched when tightening everything up |
Tools required | Screwdriver, adhesive |
What You'll Learn
Remove the screws on the switch housing
To install Electra bike grips, you need to remove the screws on the switch housing. This will separate the switch housing and allow you to remove the stock grip and install a new one.
When removing the switch housing, it's important to "shim" the brake handle out so you don't accidentally destroy the brake switch. This is a pretty easy process, but it's important to take your time and follow the directions carefully.
To remove the screws on the switch housing, you will need a screwdriver. Make sure you have the correct type and size of screwdriver for the screws on your bike. Once you have the correct screwdriver, you can remove the screws by turning them counterclockwise. It's important to be gentle and careful during this process to avoid damaging the screws or the switch housing.
After removing the screws, you can separate the switch housing and remove the old grip. If you're installing new grips on the left side of the handlebars, you may need to cut the old grip off. Once the old grip is removed, you can add adhesive to the leading edge of the new grip, position and orientate it the way you want, and slide it on.
Fixing an Electric Mini Bike: Troubleshooting and Maintenance Guide
You may want to see also
Shim the brake handle out to avoid damaging the brake switch
To install Electra bike grips, you must first remove the screws on the switch housing, separating it and removing the stock grip. You then need to shim the brake handle out to avoid damaging the brake switch. This is done by following the directions provided with the grips. Once the switch housing is removed, you can cut the left side grip off, add adhesive to the leading edge of the grip, position and orientate the grip the way you want it, and slide it on. It is important to take your time and ensure that the wires are not pinched when tightening everything up.
Electric Bike Graphics: Visual Communication Strategies
You may want to see also
Cut the left side grip off
To cut the left side grip off, you must first remove the screws on the switch housing. This will separate the switch housing from the grip. You can then cut the left side grip off.
It is important to note that you should shim the brake handle out so you do not accidentally destroy the brake switch when removing the switch housing. You should also take your time and follow the directions carefully when installing new grips. When tightening everything up, ensure the wires are not pinched.
Discovering Indego Electric Bikes: A Guide to Finding Your Ride
You may want to see also
Add adhesive to the leading edge of the grip
To install Electra bike grips, you must add adhesive to the leading edge of the grip. This is done by removing the screws on the switch housing, separating it, and cutting the left-side grip off. You can then add the adhesive to the leading edge of the grip, position and orientate the grip, and slide it on.
Electric Biking Basics: A Beginner's Guide to E-Biking
You may want to see also
Position and orientate the grip
Positioning and orientating the grip is a key part of the installation process. Once you have removed the screws on the switch housing, separated it, and cut the left side grip off, you can add adhesive to the leading edge of the grip. You should then position and orientate the grip the way you want it and slide it on.
If you find that the grip is hard to slide on, you can try splashing some rubbing alcohol inside the grip. Once in position on the bar, the alcohol will evaporate after about 20 minutes, causing the grip to stay put. Alternatively, you can wipe the inside with a little dish soap or a similar substance before twisting the grip into place.
Unleashing Your Bosch Electric Bike: Removing Restrictions
You may want to see also
Frequently asked questions
First, remove the screws on the switch housing and separate it. Then, cut the left side grip off, add adhesive to the leading edge of the grip, position and orientate the grip the way you want it, and slide it on.
You have to "shim" the brake handle out so you don't accidentally destroy the brake switch.
You may accidentally destroy the brake switch.
You may pinch the wires when tightening everything up.
You may start throwing DTCs.