Installing A Fender On Your Nakto Electric Bike

how to install fender on nakto electric bike

Installing a fender on a Nakto electric bike is a complex process that requires a number of tools, including a 4mm and 3mm allen key, and an 18mm, 15mm, and 10mm wrench. The first step is to remove the front tire, followed by the headlight, which is secured in the same place as the fender. The fender is then placed in the middle of the front fork, with the notch on its top slotting underneath the headlight. The fender is then tightened into place, with care taken to ensure it doesn't rub against the tire. The headlight is then replaced and adjusted to illuminate the road ahead without blinding oncoming traffic. It is recommended that you consult a certified, reputable bike mechanic to assist with the installation.

Characteristics Values
Tools 4mm and 3mm allen key, 18mm, 15mm and 10mm wrench
First step Remove the front tire
Next step Remove the headlight using a 4mm allen key and 10mm wrench
Then Place the fender in the middle of the front fork, with the notch on its top slotting underneath the headlight
After that Put the headlight back with the bolt, threading it into the notch and fork hole
Finally Tighten with the allen key and wrench

shunzap

Removing the mounting bolts from the fork

To remove the mounting bolts from the fork of a Nakto electric bike, you will need a 4mm and 3mm allen key to assemble and mount the fenders. You will also need an 18mm, 15mm, and 10mm wrench to remove the wheel and other parts of the bike to make the installation easier. Before installing the front fender, you will need to remove the front tire.

To remove the bolts, first use the 4mm allen key to slot in the front and hold the bolt in place. Then, use the 10mm wrench to loosen the nut on the back. Once the nut is loose, pull the bolt out.

It is important to note that the adjustment of the front brake system can be difficult. If you are unsure about any part of the process, it is recommended that you consult a certified, reputable bike mechanic for assistance.

shunzap

Assembling the fender

To assemble the fender on your Nakto electric bike, you will need a 4mm and 3mm allen key, as well as an 18mm, 15mm and 10mm wrench. Before installing the front fender, you will need to remove the front tire.

First, place the notch of the fender against the hole on the front of the fork. Then, remove the headlight using a 4mm allen key and 10mm wrench. The allen key will slot in the front and hold the bolt in place as the 10mm wrench loosens the nut on the back. Pull the whole bolt out and then position the front fender in place.

Once the fender is in place, put the headlight back with the bolt and thread it into the notch and fork hole. Push it all the way up to prevent the fender from rubbing against the tire. When the parts are properly aligned, tighten it down with the same allen key and wrench you used before.

Finally, centre the headlight and adjust the angle slightly downwards to illuminate the road ahead without blinding oncoming traffic. Loosen the headlight angle adjustment bolt with a Phillips-head screwdriver, tilt the headlight to the optimal position, and then tighten it in place securely.

shunzap

Removing the front tire

To remove the front tire of your Nakto electric bike, you will first need to remove the headlight. To do this, use a 4mm allen key and a 10mm wrench. The allen key will slot into the front and hold the bolt in place as the 10mm wrench loosens the nut on the back. Once the nut is loose, pull the whole bolt out.

Now, you can remove the front tire. To do this, you will need an 18mm, 15mm, and 10mm wrench to remove the wheel and other parts of the bike. This will make installing the fender easier.

Once the front tire is removed, you can begin assembling the fender. You will need a 4mm and 3mm allen key to assemble and mount the fender. Place the notch of the fender against the hole on the front of the fork. Then, place the headlight back with the bolt and thread it into the notch and fork hole. Push it all the way up to prevent the fender from rubbing against the tire. Once it is threaded through and the parts are properly aligned, tighten it down with the allen key and wrench.

shunzap

Adjusting the headlight

To adjust the headlight on your Nakto electric bike, you'll need to use a Phillips-head screwdriver to loosen the headlight angle adjustment bolt. Tilt the headlight to the optimal position and then tighten it securely in place. This will ensure that the headlight illuminates the road ahead without blinding oncoming traffic.

  • Loosen the headlight angle adjustment bolt using a Phillips-head screwdriver. This will allow you to adjust the angle of the headlight.
  • Slightly tilt the headlight downwards. The goal is to illuminate the road ahead without causing glare for oncoming traffic.
  • Once you've found the optimal position, tighten the bolt securely in place. This will ensure that the headlight stays in the desired position.
  • Test the headlight at night or in a dark area to ensure it is properly adjusted and provides adequate illumination for your rides.

Remember to consult the bike's manual or seek assistance from a certified bike mechanic if you have any doubts or encounter any issues during the adjustment process.

shunzap

Consulting a certified bike mechanic

If you're unsure about installing a fender on your Nakto electric bike, it's best to consult a certified, reputable bike mechanic. They will be able to advise on the correct tools and parts needed, as well as guide you through the process if you'd like to attempt the installation yourself.

A bike mechanic will have the necessary tools and expertise to ensure the fender is installed correctly and safely. They will be able to remove the mounting bolts from the fork and pass the bolt through the arm mount and fork mounting point, ensuring the fender is centred and secure.

The mechanic can also adjust the headlight, loosening the angle adjustment bolt with a Phillips-head screwdriver and tilting the light to the optimal position before tightening it securely. They will also be able to advise on any necessary adjustments to the front brake system, which can be a complex process.

By consulting a certified bike mechanic, you can ensure that your electric bike is in safe hands and that the fender installation is completed to a high standard.

Frequently asked questions

You will need a 4mm and 3mm allen key to assemble and mount the fender, as well as an 18mm, 15mm, and 10mm wrench to remove the wheel and other parts of the bike to make the installation easier. First, remove the front tire and the headlight. Then, place the notch of the fender against the hole on the front of the fork, and put the headlight bolt back in place. Push it all the way up to prevent the fender from rubbing against the tire. Once it is threaded through and the parts are properly aligned, tighten it down with the same allen key and wrench you used before.

You will need a 4mm and 3mm allen key to assemble and mount the fender, as well as an 18mm, 15mm, and 10mm wrench to remove the wheel and other parts of the bike to make the installation easier.

Yes, you will need to remove the front tire before installing the fender.

Written by
Reviewed by
Share this post
Print
Did this article help you?

Leave a comment