Umair Gaines
Sunbeam Products, Inc. manufactures heated bedding products, including electric blankets and heated mattress pads, that can be found in over 25 million households. Setting up a Sunbeam electric blanket is straightforward. First, lay the blanket on the bed with the label at the foot of the bed, facing upwards. Then, connect the cord to the module at the bottom of the blanket and run the cord along the floor under the bed. Place the warming control at the headboard, and if your blanket has dual controls, place one on each side of the bed. To preheat the blanket, press the On/Off button and then the “Preheat” button. The blanket will warm for 30 minutes before returning to its previous setting.
Explore related products
What You'll Learn
Positioning the blanket
To set up your Sunbeam electric blanket, start by laying it on your bed. Make sure that the label affixed to the blanket is positioned at the foot of the bed, facing upward. This label is important as it indicates which side of the bed the primary control operates. The primary control operates the right side of the bed when viewed from the foot. If you have a remote control, it will be labelled to indicate whether it operates the left or right side.
Next, connect the cord to the module at the bottom of the blanket, close to the label. You will know that the cord is connected when you hear the plastic hinges click into place. Ensure that the cord is not wedged between the mattress and box spring, and that it does not get pinched or tangled.
Now, place the warming control on either side of the bed, near the headboard. If your blanket has dual controls, simply place one on each side of the bed. The control will feel warm to the touch when it is functioning properly, so don't be alarmed if it feels slightly warm.
Finally, plug the main power cord into a 110-volt or 120-volt wall outlet. You can now turn on your electric blanket and adjust the settings according to your preferences.
Electrical Wiring: A Guide for Your Home
You may want to see also
Explore related products
Connecting the cord
To connect the cord, start by laying the electric blanket on your bed with the label facing upward at the foot of the bed. You should then connect the cord to the module at the bottom of the blanket, near the label. You will know it is connected when you hear the plastic hinges click into place. Make sure the control cord is connected to the connection module.
Once connected, run the cord along the floor under the bed. Ensure that it is not wedged between the mattress and box spring, and that it does not get pinched or tangled. Place the warming control on either side of the bed near the headboard. If your blanket has dual controls, set one on each side of the bed.
If you are having trouble getting your electric blanket to heat properly, try the following:
- Fold the blanket three times over.
- Ensure the control cord is connected to the module.
- Plug the power cord into an outlet.
- Turn on the blanket and set the control to the highest setting.
- Wait 5 to 7 minutes, then put your hand between the folds.
Electric Razors: Allowed in Carry-Ons or Checked Bags?
You may want to see also
Explore related products
Placing the warming control
To set up your Sunbeam electric blanket, you'll need to pay close attention to the placement of the warming control. This is what ensures your comfort and safety while using the product.
First, lay the electric blanket on your bed, ensuring that the label is at the foot of the bed and facing upwards. The warming control should be placed on either side of the bed, positioned near the headboard. This control unit is what allows you to adjust the temperature and settings of your electric blanket. If your blanket features dual controls, place one on each side of the bed, as these allow for individualised temperature preferences.
The control with the service label is the primary control. When looking at the bed from the foot, the primary control operates the right side. If you have a remote control, it will be labelled to indicate whether it controls the left or right side. Always refer to your user manual to confirm the correct setup for your specific model, as some may have unique requirements.
It's important to note that the control unit will feel warm to the touch when functioning properly. To test if your blanket is heating up correctly, perform the fold test. First, locate the control in the centerfold of the folded blanket and ensure the control cord is connected to the module. Then, plug the power cord into a 110-volt or 120-volt wall outlet and turn on your blanket. Set it to the highest setting and wait 5 to 7 minutes before checking if it's warming up.
Electric Showers: Preventing Limescale, Maintaining Performance
You may want to see also
Explore related products
Preheating
To preheat your Sunbeam electric blanket, first lay the blanket on your bed with the label facing upwards at the foot of the bed. Next, connect the cord to the module at the bottom of the blanket—you will know it is connected when you hear the plastic hinges click. Then, place the warming control at the head of the bed. Once you have done this, simply press the "On/Off" button once and then hit the "Preheat" button. The blanket will then warm for 30 minutes before returning to its previous setting.
It is important to note that, during the pre-heat cycle, the blanket will return to the heat setting of the schedule after 30 minutes. While pre-heating, you cannot use Alexa to increase the temperature as the pre-heat function is set to the highest setting.
If you would like to test if your blanket is heating up properly, try the following: First, fold the blanket three times over. Then, make sure the control cord is connected to the module and plug the power cord into an outlet. Turn on the blanket and set it to the highest setting. After 5 to 7 minutes, put your hand between the folds and you should feel the blanket warming up.
If you are using the Sunbeam app, you can change the automatic 10-hour auto-off setting by pressing the timer icon. The timer can be set up to 10 hours in 0.5-hour increments, or you can choose the "Stay On" option to keep the blanket on for 24 hours.
Igniting Your Electric Start Furnace: A Step-by-Step Guide
You may want to see also
Explore related products
Washing and drying
To wash your Sunbeam electric blanket, start by presoaking it for 15 minutes in mild soap and cold water. Then, wash it in the machine with mild soap and cold water on the "delicate" or "gentle" cycle for two minutes. Avoid using bleach. Rinse it in fresh, cold water, then spin dry in the washing machine. After spinning it dry, gently shape it to its original size.
When drying your Sunbeam electric blanket, do not use a commercial dryer or a dryer at a Laundromat as they can get too hot and damage the wiring. Instead, preheat your home dryer on the "low" temperature setting for 2 minutes. Then, dry the blanket for 10 minutes at a low temperature. Remove the blanket from the dryer while it is still damp and gently reshape it to its original size. Finally, drape the blanket over a clothesline or shower rod to finish drying.
Cutting Electrical Cover Plates: Is It Safe to Modify?
You may want to see also
Frequently asked questions
First, lay the blanket on the bed with the label at the foot of the bed, facing upward. Then, connect the cord to the module at the bottom of the blanket and run the cord along the floor under the bed. Place the warming control at the headboard.
Press the "On/Off" button once and then press the "Preheat" button. The blanket will warm for 30 minutes before returning to its previous setting.
Try the fold test: fold the blanket 3 times, connect the control cord to the module, plug the power cord into an outlet, turn on the blanket, set it to the highest setting, and wait 5-7 minutes. Put your hand between the folds—you should feel the blanket warming up.
The control will feel warm to the touch when functioning correctly. Note that warming blankets will not feel hot to the touch when laid out flat.
Yes, but Alexa only works on settings 1 (L) to 10 (H) and will not allow temperature adjustments beyond these levels. Additionally, Alexa will not increase the temperature during pre-heating as it is already set to the highest setting.
