Beatrice Lang
Electric bikes are a great way to get around, and the Cyclone is a popular model. If you're thinking of getting one, there are a few things you should know about how to get started. First, you'll need to measure your bike and determine if it's compatible with the Cyclone. You'll also need to make sure you have the right tools for the job, as installation can be tricky.
What You'll Learn
Measuring the bike
To start a Cyclone electric bike, you will first need to measure the bike. This will involve measuring the width of the bottom bracket shell, from face to face. Do not measure any bearings or other pieces, you are looking for the bottom bracket shell width only. Measure it twice. 99.9% of the time, this will be a measurement between 68mm and 120mm. If it is not, then it is an install that is outside the scope of this article.
To measure the bottom bracket shell, you will need to remove the bottom bracket from the bottom bracket shell using the appropriate tools. This is a job for your local bike shop if you do not have the tools, patience or know-how.
It is important to note that you must have a threaded bottom bracket for the Cyclone to fit. If you are unsure whether your bicycle has an IS threaded bottom bracket, take it to your local bike shop and have them find out.
Once you have measured the bike and determined that you have a threaded bottom bracket, you can move on to the next steps of installing the Cyclone. The installation difficulty varies, but the initial installation is fairly straightforward if you have the right tools. The hardest part is usually making it look neat, as the stock controller has a few extra cables that you may not need.
Mastering Electric Dirt Bike Wheelies: A Step-by-Step Guide
You may want to see also
Compatibility
It is also important to determine whether your bike has a threaded bottom bracket. This information can be obtained by consulting a local bike shop. If your bike does have a threaded bottom bracket, there is a high likelihood that the Cyclone will fit.
Additionally, the compatibility of the Cyclone electric bike may depend on the specific model of your bicycle. Different models may have varying bottom bracket shell sizes and thread types, which can impact the compatibility and installation process.
By following these steps and considering the specific measurements and characteristics of your bicycle, you can ensure compatibility and a smooth installation process for your Cyclone electric bike.
Selecting the Right Battery for Your Electric Bike
You may want to see also
Installation instructions
The Cyclone 3000W electric bike kit can be installed on most pedal-power bicycles, but it is important to note that it is not suitable for children. The installation difficulty varies, but the initial installation is fairly straightforward if you have the right tools. First, you need to make sure you have a threaded Bottom Bracket. If you don't know if your bicycle has an IS threaded bottom bracket, take it to the local bike shop and have them find out. Once you've determined that you have an IS threaded bottom bracket, it is very likely the Cyclone will fit.
Next, you need to measure the width of the bottom bracket shell, from face to face. Do not measure any bearings or other pieces, you are looking for the bottom bracket shell width only. Measure it twice. 99.9% of the time, this will be between 68mm and 120mm. If it's not, then it is an install that is outside the scope of this article. Remove the bottom bracket from the bottom bracket shell using the appropriate tools, this is a job for your local bike shop if you don't have the tools, patience or knowhow.
To achieve optimal performance, the Cyclone 3000W Ebike Kit requires a suitable battery. A 52-volt battery with Samsung 25r or 30q cells, or a GA pack with plenty of capacity to provide ongoing high current, is ideal. A 20ah pack is highly recommended, along with a 50-amp capacity BMS. With the right battery, you can expect the bike to be fully charged in just 4-5 hours, allowing you to get back on the road quickly.
The hardest part is usually making it look pretty. The stock controller has a few extra cables that you most likely won't need, so hiding those and running the cables in a tidy manner can be a bit of a challenge. However, it can certainly be made to look great if you are willing to spend the time.
Pedal Assist Sensor Installation: A Guide for Electric Bikes
You may want to see also
Hiding extra cables
The Cyclone 3000W electric bike has some extra cables that you will most likely not need. These extra cables are for additional functionality that you may not require. To start with, you only need five connections. The installation can be a bit of a challenge, but it can certainly be made to look great if you are willing to spend the time.
To hide the extra cables, you can try the following:
- Gather all the extra cables together and tie them neatly with cable ties.
- Find a discreet location on the bike to route the cables through, such as along the frame or under the seat.
- Use cable clips or zip ties to secure the cables in place, making sure they are tight and do not move around.
- Consider using cable sleeves or spiral wraps to further conceal and protect the cables.
- Test the bike to ensure that the cables are not interfering with the movement of the bike or any other components.
By following these steps, you can effectively hide the extra cables on your Cyclone electric bike and achieve a neat and tidy installation.
Electric Fat Bike Revolution: Powering Your Off-Road Adventure
You may want to see also
Tools needed
To start installing a Cyclone electric bike, you will need the following tools:
- A measuring tape to measure the width of the bottom bracket shell.
- Tools to remove the bottom bracket from the bottom bracket shell. If you don't have these, you can take your bike to a local bike shop.
- An adapter to make the bottom bracket shell standard BSA diameter, if it is not already. Make sure this is threaded or it won't work.
- A threaded bottom bracket. If you're not sure if your bike has one, take it to a local bike shop to find out.
The initial installation is fairly straightforward if you have the right tools, but making it look neat can be a challenge due to the stock controller's extra cables.
Electric Scooter Motor on a Bike: A How-to Guide
You may want to see also
Frequently asked questions
You can use a bump key that matches the type of lock on your electric bike. You can buy these online or from specialist retailers. Insert the bump key into the lock and apply a small amount of force while tapping or 'bumping' the key. This jostles the tumblers inside the lock, allowing you to turn it. Alternatively, you can use a screwdriver as a temporary key alternative. Insert it gently into the ignition slot and turn it as you would with a regular key.
First, make sure the battery is charged. Then, select your preferred riding mode using the controls on the handlebar. You can choose from low to high assistance, or a throttle mode which allows you to ride without pedalling. Once your bike is powered up and the mode is selected, you can start riding. In pedal-assist mode, you just need to start pedalling and the motor will engage automatically.
You can carefully cut and join the power source wires together to create a connection and power up your electric bike. However, this is only a temporary fix and should be used for short journeys. Make sure to wear rubber gloves to prevent electric shocks.
Most e-bikes come with a removable battery that you can charge separately, or you can charge it directly on the bike.
