Trystan Casey
Lansinoh breast pumps are known for their quiet motors and comfort, and they offer a wide range of models to choose from. Before assembling your Lansinoh breast pump, it is important to ensure that all the parts have been cleaned and sterilized. This can be done by disassembling the pump and placing the parts in a pan of boiling water for sterilization. After sterilization, it is important to air-dry all parts completely and inspect them for any cracks or damage. Once the parts are clean and dry, you can start assembling the pump by placing the silicone diaphragm on top of the flange body and securing it in place. Next, attach the ComfortFit® flange, the valve, and the collection bottle. Finally, connect the tubing to the bottle and the Y connector. With your pump assembled, you can now follow the instructions for use, which include pressing the power button to initiate the letdown phase and adjusting the suction strength as needed.
| Characteristics | Values |
|---|---|
| Assembly | Place the purple silicone diaphragm feet down on the top of the flange body. Ensure the diaphragm fits securely between the rims of the breast flange body. Place a clear diaphragm cap over the breast flange body and twist to secure. Push the ComfortFit® flange into the breast flange body. Secure the valve to the bottom of the breast flange body. Ensure the tubing is pushed all the way over the port. Screw the collection bottle onto the breast flange body and attach the tubing to the Y connector. |
| Motor | Quiet |
| Suction Strength | 8 levels of adjustable suction |
| Pumping Styles | Customizable pumping styles that mimic a baby's natural suckling patterns |
| Phases | Letdown phase and expression mode |
| Letdown Phase | Initiated by pressing the power button; lasts two minutes |
| Expression Mode | Can be entered directly by bypassing the letdown phase using the letdown/expression toggle button |
| Stimulation Mode | Can be used before expression mode |
| Cleaning | Wash hands and ensure the pump is sanitized before use. Various parts can be washed in the dishwasher or by hand with dish soap and hot water. |
| Sterilization | Disassemble the breast pump, boil the parts in water for 5 minutes, and air dry on a clean surface. |
Explore related products
What You'll Learn
Sterilise and clean all parts
Sterilising and cleaning your Lansinoh breast pump is critical to prevent germs from growing in breast milk residue. Before the first use, sanitise the breast pump by placing it in boiling water for 5 minutes, then allowing it to cool and air dry.
After each use, wash the pump in hot soapy water, either by hand or on the top rack of the dishwasher. Smaller parts can be placed in a mesh laundry bag. Rinse all parts with clean water and allow them to air dry on a clean towel or drying rack. Make sure all parts are completely dry before using the pump again.
The tubing, Y connector, and white pump connector should never be washed or sterilised. All other parts, excluding the tubing, connector, and pump connector, are dishwasher safe, but the white valves and diaphragms should be gently hand-washed, as they are delicate and can affect the pump's performance if damaged.
All parts, excluding the tubing, white pump connector, and breast cushions, can be steam-sterilised in a microwave bag according to the manufacturer's directions.
Tightening Electric Clutch Nuts: How Much is Too Much?
You may want to see also
Explore related products
Assemble the diaphragm and flange body
To assemble the diaphragm and flange body of the Lansinoh electric breast pump, follow these steps:
Firstly, ensure that you have washed and sterilised all parts of the pump, including the diaphragm and flange body, following the instructions in the cleaning and sterilisation section of the manual. It is important to have clean hands when assembling the pump. Place the purple silicone diaphragm feet down on the top of the flange body, ensuring it fits securely between the rims of the breast flange body.
Next, take the clear diaphragm cap and place it over the breast flange body. Twist the cap to secure it in place, ensuring that the tubing portal faces the back of the pump. Push the ComfortFit® flange into the breast flange body firmly. Now, hold the base of the white valve and gently secure it to the bottom of the breast flange body. Ensure that the tubing is pushed all the way over the port and completely covers it for proper suction.
It is important to follow the assembly instructions carefully to ensure the pump functions correctly and safely.
Diagnosing Electric Scooter Fuses: A Quick Guide
You may want to see also
Explore related products
Connect the tubing and collection bottle
To connect the tubing and collection bottle, start by placing the purple silicone diaphragm feet down on the top of the flange body. Ensure that the diaphragm fits securely between the rims of the breast flange body. Place a clear diaphragm cap over the breast flange body and twist it to secure it, ensuring that the tubing portal faces the back of the pump. Push the ComfortFit® flange into the breast flange body firmly.
Now, hold the base of the white valve and gently secure it to the bottom of the breast flange body. Ensure that the tubing is pushed all the way over the port and completely covers it. Screw the collection bottle onto the breast flange body. Make sure that the bottle is screwed on tightly and securely.
Attach the other end of the tubing to the Y connector. Check that the tubing is connected securely and will not come loose easily. Once assembled, always remember to wash your hands before pumping and make sure the pump is sanitized and assembled correctly.
Before the first use, it is important to sterilize all parts of the pump. Disassemble the breast pump and place the parts into a large pan. Cover the parts with water, ensuring there is enough room for the parts to float. Bring the water to a boil and boil for 5 minutes to sterilize. Remove the parts from the water and allow them to air dry completely on a clean surface before reassembling and using.
Adjusting Torque: Electric Drill Maintenance 101
You may want to see also
Explore related products
Wash your hands and breasts
Before you start assembling your Lansinoh breast pump, it is important to practice good hygiene to ensure the safety of both you and your baby.
First, wash your hands thoroughly. Use soap and warm water, and scrub your hands for at least 20 seconds. Make sure to clean between your fingers and under your nails. Rinse your hands well under running water and dry them with a clean towel.
Next, ensure that your breasts are clean. You can do this by gently washing your breasts with warm water and a mild soap. Rinse away any soap residue and gently pat your breasts dry with a soft, clean towel.
It is important to clean your breasts before each pumping session to prevent bacteria from entering the pump and the milk supply. This helps to ensure that your expressed milk is safe for your baby to consume and reduces the risk of contamination.
By following these steps and maintaining good hygiene practices, you can ensure a safe and comfortable pumping experience.
Electricity Restoration in Houston, Texas: What's the Status?
You may want to see also
Explore related products
Adjust the handle for stimulation or expression
The Lansinoh Manual Breast Pump has two pumping modes: stimulation and expression. To switch between the two modes, you need to adjust the handle.
The stimulation mode gently stimulates the breast to encourage milk let-down and to start the milk flow. To enter this mode, set the handle in the first (top) notch in the stem.
The expression mode allows you to express breast milk from the breast. To switch to this mode, set the handle in the second (bottom) notch in the stem. For the strongest suction, fully depress the handle.
The Lansinoh breast pump also has eight levels of suction strength, which can be adjusted using the control button.
Weaving Electrical Harnesses: A Step-by-Step Guide
You may want to see also
Frequently asked questions
Before assembling your Lansinoh electric breast pump, ensure that all parts have been cleaned and sterilised. Here are the steps to assemble the pump:
- Place the purple silicone diaphragm feet down on the top of the flange body.
- Ensure the diaphragm fits securely between the rims of the breast flange body.
- Place a clear diaphragm cap over the breast flange body and twist it to secure it so the tubing portal faces the back of the pump.
- Firmly push the ComfortFit® flange into the breast flange body.
- Holding the base of the white valve, gently secure the valve to the bottom of the breast flange body.
- Ensure the tubing is pushed all the way over the port and completely covers it.
- Screw the collection bottle onto the breast flange body.
- Attach the other end of the tubing to the Y connector.
Disassemble the breast pump and place the parts into a large pan. Cover the parts in water, ensuring there is room for all the parts to float. Bring the water to a boil and boil for 5 minutes to sterilise. Remove all parts from the water and let them air dry on a clean surface. Ensure that all parts are completely dry before reassembling.
Wash your hands before pumping and ensure the pump is sanitised and assembled correctly. Centre the flange opening over your nipple and gently press the pump against your breast, ensuring your nipple is centred in the flange tunnel. Start pumping by pressing the power button, which will initiate the 2-minute letdown phase. The pump will then enter expression mode. You can bypass the letdown phase by pressing the letdown/expression toggle button when turning on the pump. With eight levels of suction, you can adjust the pump's suction strength using the control button.
