Molly Ayala
If you're looking to connect a Samsung electric dryer, there are a few things you should know. Electric dryers need to be plugged into a 240 volt, 60 Hz AC outlet with a 30-amp fuse or circuit breaker on both sides of the line. The power cord is usually not included with the dryer, so you'll need to purchase one separately. Make sure you get the right cord for your outlet, which could be a 3-prong or 4-prong power cord. You'll also need to ensure that all wiring is connected correctly and that the exhaust ductwork is in place and taped. If you want to connect your dryer to Wi-Fi and control it via your smartphone, you can use the SmartThings app.
| Characteristics | Values |
|---|---|
| Power cord | 3-prong or 4-prong power cord |
| Power outlet | 240 volt, 60 Hz AC outlet with a 30-amp fuse or circuit breaker on both sides of the line |
| Drain hose | Connect to the drain-outlet directly, with the end at least 70 mm away from the drain |
| Exhaust ductwork | Use rigid or stiff-walled flexible metal duct material |
| Leveling | The dryer should be level and sitting firmly on the floor |
| Wi-Fi connection | A 2.4 GHz connection and at least 3 Wi-Fi network receiving antennas are required |
Explore related products
What You'll Learn
Electric outlet and grounding
To connect a Samsung electric dryer, you must ensure that it is plugged into a properly grounded electrical outlet. The outlet should be a 240 volt, 60 Hz AC outlet with a 30-amp fuse or circuit breaker on both sides of the line. If your home was built before 2000, you likely have a 3-prong dryer outlet and will need a 3-prong power cord. Homes built after 2000 will require a 4-prong power cord and outlet.
The power cord is not included with the dryer, so you will need to purchase one separately. You can use the cord from your previous dryer or ask your installer to provide one. If you are replacing an old dryer, you can swap the old cord for the new one by taking pictures of the old setup as a guide.
A 3-prong cord will have two hots and a combined neutral and ground. When connecting them, leave the dryer's ground terminal unused and ensure that the dryer's neutral-ground jumper is intact. Upgrading to a 4-prong outlet with new wiring is recommended for safety reasons, as it keeps the ground and neutral wires separate.
After connecting the wiring, plug the dryer into the outlet and confirm that it is grounded properly. You can test this by running a Time Dry cycle for 30 seconds and then turning the dryer off.
Electric Safety Edges: A Guide to Ordering
You may want to see also
Explore related products
![Upgraded Pulley Belt Parts for Samsung Dryer, 6602 001655 Dryer Belt and DC93-00634A Idler Pulley [Enhanced ],DC61-01215B Tension Spring,Replacement dv45h7000ew,dv48h7400ew,dv42h5000ew,dv48j7700ew](https://m.media-amazon.com/images/I/71+5iq-gj6L._AC_UY218_.jpg)
Gas connections
To connect a Samsung gas dryer, you will need a gas line, a dryer vent kit, and a water hose if you want to use the steam settings. The gas line should be made of natural or LP (liquid propane) gas and go from the pipe in your house to 3/8". If you have 1/2" gas lines in your house, you'll need to get a reducer. The dryer vent kit should be 4" and vented outside. The steam cycle works with a 3/4" water line, the same as a washer, and comes with a splitter so you can split the water supply for your washer and run a second line to the dryer.
If you do not have an existing gas line and would like to switch to gas from electric, you should contact your local gas company to ask about getting a gas line installed. If you already have a gas line installed, you can switch from gas to electric or choose a new gas dryer.
Samsung gas dryers need to be plugged into a 120-volt, 60 Hz AC outlet with a 15-amp fuse or circuit breaker. The power cord is included with the dryer. The user manual for your gas dryer will have more specific details.
To install a Samsung gas dryer, you must attach the dryer's exhaust outlet to the exhaust outtake built into the wall of your house or apartment. Use 4-inch ducting tube made of rigid aluminium or galvanised steel. If you need flexible ducting, use ducting with stiff walls rather than plastic or foil-style ducting. A stiff structure prevents crushing or collapse and reduces the risk of lint buildup, which is important because dryer lint is highly flammable. Keep the ducting as straight as possible between the dryer and the outtake, and use duct tape to attach it to the dryer and to the outtake.
Once the vent ducting is attached, you can plug the dryer in. Make sure the dryer is plugged into an outlet that has a proper ground. It should be a three-pronged outlet, rather than a two-pronged one. Confirm that the dryer is plugged into an electrical outlet and grounded properly, the exhaust ductwork is connected, the joints are taped, and you have used rigid or stiff-walled flexible metal duct material, not plastic flexible duct. The dryer should be level and sitting firmly on the floor.
Electricity Pricing: Hourly Rates and Their Money-Saving Potential
You may want to see also
Explore related products
Drain hose installation
To install the drain hose, follow the steps outlined below:
Firstly, insert the drain hose into the designated hole (marked as Hole A). Then, connect the other end of the drain hose to the drain outlet. This can be done by using the accessory hose, also known as the long drain hose, and attaching it directly to the drain outlet. Ensure that the end of the drain hose is positioned at least 70mm away from the drain. It is important to avoid submerging the end of the drain hose during installation.
If the provided drain hose is too long, utilise the accompanying cable tie to straighten and secure the hose. In some cases, it may be necessary to adjust the length of the hose by removing it from the temporary fixture (marked as Hole B) and reinserting it into Hole A. This ensures a proper fit and prevents any potential issues with drainage.
By following these steps, you can effectively install the drain hose for your Samsung electric dryer, ensuring proper drainage and preventing any potential issues caused by incorrect installation.
Establishing Power Plants: A Comprehensive Guide to Getting Started
You may want to see also
Explore related products
Wi-Fi connection
To connect your Samsung electric dryer to Wi-Fi, you will need to use the SmartThings app. This app is available on the Google Play Store, Apple App Store, and Samsung Galaxy Apps. SmartThings is a function that allows you to control and manage smart home appliances and Internet of Things (IoT) devices with your smartphone.
Before connecting your smartphone with your dryer, ensure that your smartphone is connected to a Wi-Fi network. On your smartphone, go to Settings -> Connection -> Wi-Fi -> Select a router to connect to (enter the password when setting the security). When connected properly, the selected router in the current network will be confirmed as “connected”.
Next, ensure that your dryer and Wi-Fi router are connected to a power source. Then, launch the SmartThings app and tap the plus button, selecting "Add device" on the home view. For FlexDry, press the "Smart Control" button on the front-load dryer. If your dryer has an LCD touchscreen, go to "Settings" and press "EasyConnect".
On your iPhone, open the Settings app and go to Wi-Fi to connect to the network name that starts with "dryer". The password is "1111122222" ("1" five times and "2" five times). Once your iPhone is connected to the Wi-Fi network, run the SmartThings app again. Enter your Wi-Fi information and tap "Next". The Wi-Fi information will be sent to the dryer.
Finally, wait until the dryer is registered with your Samsung account. To set up a Samsung account, you can follow the directions provided by the SmartThings app. Alternatively, if you have a Samsung smartphone, you can add your Samsung account in the settings app, which will automatically sign in.
Braun 7893s Electric Shaver: Master the Art of Smooth Shaving
You may want to see also
Explore related products
Power cord installation
To install the power cord for a Samsung electric dryer, follow these steps:
Firstly, ensure you have purchased a power cord that is compatible with your dryer and outlet. Electric dryers need to be plugged into a 240-volt, 60 Hz AC outlet with a 30-amp fuse or circuit breaker on both sides of the line. If your home was built before 2000, you will likely have a 3-prong outlet, requiring a 3-prong power cord. Homes built after 2000 usually have a 4-prong outlet, requiring a 4-prong power cord.
If you are replacing an old dryer, you can use the power cord from your previous dryer, or your installer may be able to provide one. Take pictures of the old setup to use as a guide for connecting the new dryer.
When connecting the power cord, if you have a 3-prong cord, connect the two hots and the combined neutral and ground. Leave the dryer's ground terminal unused, and ensure the dryer's neutral-ground jumper is intact.
After connecting the power cord, confirm that the dryer is plugged into a properly grounded outlet and that the exhaust ductwork is connected and taped. Use rigid or stiff-walled flexible metal duct material, not plastic flexible duct.
Finally, test the dryer by starting a Time Dry cycle for 30 seconds and then turning it off. Ensure the dryer starts, runs, heats, and shuts off properly.
Electric Lawn Mowers: Self-Propelled or Not?
You may want to see also
Frequently asked questions
First, ensure that your dryer and Wi-Fi router are connected to a power source. Then, download and install the SmartThings app on your smartphone. Sign in to your Samsung account and tap the plus button to select "Add device". On your iPhone, open the Settings app and connect to the Wi-Fi network name that starts with "dryer".
Electric dryers need to be plugged into a 240 volt, 60 Hz AC outlet with a 30-amp fuse or circuit breaker on both sides of the line. You will need either a 3-prong or 4-prong power cord, depending on your outlet.
Yes, you can stack your Samsung dryer on top of a matching Samsung washer using the SK-5A Stacking Kit accessory.
To remove the child lock on most models, press and hold the Time and Signal buttons simultaneously until the Child Lock icon disappears from the display.
Connection to water is optional for Samsung dryers. If you do choose to connect to water, you will need both hot and cold water faucets along with a "Y" type splitter, which comes with either the dryer or washer.
