A Beginner's Guide To Installing Electric Bike Kits From Youtube

how to install electric bike kit on u tube

There are many videos on YouTube that can teach you how to install an electric bike kit. The first step is to order a motor kit and battery, along with a small set of bike tools and a freewheel remover tool. The next step is to deflate the tire and use a set of tire levers to pop the tire off. You can then transfer the tube and tire to the new wheel and install your old freewheel onto the hub. Finally, you can install the cruise control switch, e-brake, and speed shifter on the right handlebar.

Characteristics Values
Installation location Drink bottle mount on the bike's frame
Installation process Remove the rear wheel, loosen the brake cable, release the wheel's quick-release lever, hold down the rear derailleur while lifting the wheel, use a freewheel remover tool and a 1" socket to remove the freewheel
Tools required Small set of bike tools, freewheel remover tool, tire levers, 1" socket
Components Motor kit, battery, cruise control switch, e-brake, 7-speed shifter
Considerations Existing gears can be utilised, potential for increased drivetrain wear, hub motor location (front or rear) depends on the model

shunzap

How to install a hub motor conversion kit

To install a hub motor conversion kit, you will need a small set of bike tools and a freewheel remover tool. The first step is to remove the rear wheel by loosening the brake cable and then the wheel's quick-release lever. Hold down the rear derailleur while lifting up on the wheel to remove it. Next, deflate the tire and use a set of tire levers to pop the tire off. Transfer the tube and tire to the new wheel and install your old freewheel onto the hub, using the included washer as a spacer to prevent the freewheel from binding. On the right handlebar, install the cruise control switch, the remaining e-brake, and the 7-speed shifter that came with your bike. Hub motor conversion kits are housed inside the hub of a wheel and can be installed in the front or rear, though rear installation is usually required for more powerful motors.

shunzap

Removing the rear wheel

If you plan to reuse your existing tube and tire, deflate the tire and use a set of tire levers to pop the tire off. Transfer the tube and tire to the new wheel, and install your old freewheel onto the hub, using the included washer as a spacer to prevent the freewheel from binding.

shunzap

Reusing the existing tube and tire

If you're planning to reuse your existing tube and tire, you'll first need to deflate the tire and use a set of tire levers to pop the tire off. Then, transfer the tube and tire to the new wheel. Install your old freewheel onto the hub, using the included washer as a spacer to prevent the freewheel from binding.

The first step to installing the hub motor is to remove the rear wheel. Loosen the brake cable and the wheel's quick-release lever. Hold down the rear derailleur while lifting up on the wheel to remove it. If your bike has a 7-speed freewheel, use a freewheel remover tool and a 1" socket to remove it.

On the right handlebar, install the cruise control switch, the remaining e-brake, and the 7-speed shifter that came with your bike.

shunzap

Installing the cruise control switch

Start by loosening the brake cable, as this will give you more room to work. Next, locate the e-brake and remaining 7-speed shifter. These components are typically found on the right handlebar and are essential for the cruise control switch to function properly.

With these parts identified, you can now install the cruise control switch. Ensure that all connections are secure and that the switch is firmly in place. Once installed, test the switch to ensure it functions as intended.

By following these steps, you can successfully install the cruise control switch on your electric bike kit, enhancing your riding experience and providing you with greater control over your speed.

shunzap

Using a freewheel remover tool

To install an electric bike kit, you will need a freewheel remover tool. This is designed for the removal of most freewheels with a 12-spline tool fitting, including Shimano, Sachs Aris, SunRace, and others.

To use a freewheel remover tool, you will also need a large wrench to turn the tool. This can be a 1" combination wrench, or an adjustable wrench (12" minimum, 15" is better). Freewheels can be difficult to remove because they are on so tight, so you will need good leverage to loosen it up.

Turn the removal tool counterclockwise using a large adjustable wrench, 1″ socket with handle, or other appropriate wrench. It will typically require some force to turn the freewheel. Turn the remover only 1 full revolution counterclockwise. Loosen and remove the skewer before continuing to remove the freewheel. Continue to turn the remover counterclockwise until the freewheel is unthreaded from the hub. Lift the freewheel from the hub.

If you have a bench vise, put the tool in the wheel, then the other end of the remover in the vise.

Frequently asked questions

The first step is to remove the rear wheel.

The Magic Pie kit recommends a 7-speed freewheel.

Yes, you can reuse your existing tube and tire.

Hub motor conversion kits are housed inside the hub of a wheel.

You can install these on the right handlebar.

Written by
Reviewed by
Share this post
Print
Did this article help you?

Leave a comment