Wiktor Wise
Swingline staplers come in a variety of models, but they all open in a similar way. If your Swingline electric stapler is jammed, you can try disconnecting the power and sliding a putty knife or flat-bladed screwdriver under the front edge to lift it back into position. If that doesn't work, there may be internal damage. To open a Swingline stapler, you can press the button on the back end to pop out the staple tray. You can also try pulling the tray with your free hand while holding the base of the stapler steady with the other hand.
Explore related products
$24.19 $27.99
What You'll Learn
- How to open a Swingline stapler: press the button on the back end to pop out the staple tray?
- Removing staples from a jammed Swingline stapler: use pliers to pull out any stuck staples
- Clearing a jammed Swingline stapler: disconnect the power, then use a flat blade to lift the stapler back into position
- How to open a Swingline Strongarm 113 stapler: push down on the unpainted metal part behind the clip to remove it?
- How to load staples into a Swingline stapler: place staples legs-down in the tray, as close to the front end as possible?
How to open a Swingline stapler: press the button on the back end to pop out the staple tray
To open a Swingline stapler, you must first set the stapler down on a table. Locate the small button on the stapler's back end, which is either on the top or bottom edge, and press it to pop out the staple tray. You may also need to remove a small piece of plastic covering the tray. Once the tray is exposed, pull it towards you with a steady grip on the stapler's base to avoid spilling loose staples.
The process of refilling the stapler begins with placing new staples legs-down in the tray, ensuring they are as close to the front end as possible. Push any unused staples forward to create additional space and prevent jamming. After loading the staples, push the tray back into the stapler until it locks into place. Test the mechanism by tipping the stapler towards you to ensure the tray remains secure.
If your Swingline stapler is jammed, you can fix it by emptying out any old staples and using pliers to extract any stubborn remnants. Place the stapler on a flat surface, leaving the jaws open. Locate the follow block, a small metal latch on the backside near the bottom edge, and push it in to loosen the mechanism. Pull the follow block upwards to release the hooks, and then pull it towards you to expose the jammed staples.
Once you have cleared the jam, slide the follow block back into the stapler to lock it in place. Load the staples legs-down at the front end of the tray, and slide the tray back into the stapler. If the tray does not lock in place, push down on the follow block to engage the hooks and secure the tray. Finally, turn the knob on the stapler's base to ensure the tray is securely fastened before using the stapler again.
The Haunting, Bleak Atmosphere of Do Androids Dream of Electric Sheep
You may want to see also
Explore related products
Removing staples from a jammed Swingline stapler: use pliers to pull out any stuck staples
If your Swingline electric stapler is jammed, you can try the following steps to remove any stuck staples. Firstly, disconnect the power to the stapler. Then, try to slide a putty knife or a flat-bladed screwdriver under the front edge, where the staples would usually come out, to lift up the mechanism and get it back into position. There may be a bent staple partway in the feed hole that you will need to pry out with a pair of needle-nose pliers.
If you can see the staple pusher at the back of the stapler, you can try to eject the staples by pushing down on it. However, be aware that staples may be ejected from the front of the stapler, so be prepared for this. Alternatively, you can remove the pusher before removing the front plate.
If the above steps do not work, there may be internal damage to the stapler.
The History of Electricity in Homes: A Timeline
You may want to see also
Explore related products
Clearing a jammed Swingline stapler: disconnect the power, then use a flat blade to lift the stapler back into position
If your Swingline electric stapler is jammed, first disconnect it from its power source. Next, take a flat-bladed screwdriver or a putty knife and carefully slide it under the front edge of the stapler—this is the part where the staples are usually ejected from. Gently try to lift the stapler back into its original, functional position.
There may be a bent staple stuck in the feed holes, which you can try to pry out with a pair of needle-nose pliers. If this doesn't work, there may be internal damage to the stapler. Unfortunately, these types of staplers are often irreparable due to a lack of available parts and high repair costs.
James Watt's Electricity Legacy: Innovations and Advancements
You may want to see also
Explore related products
How to open a Swingline Strongarm 113 stapler: push down on the unpainted metal part behind the clip to remove it
To open a Swingline Strongarm 113 stapler, follow these steps:
First, set the stapler on a flat surface and ensure the jaws are open. This will give you a stable base to work on and make it easier to access the internal components. Next, locate the unpainted metal part behind the clip. This metal part is likely the 'follow block', which is a spring-loaded mechanism that holds the staples in place. Push down on this unpainted metal part and remove it. It may require some force, so be sure to apply pressure firmly and directly downwards. If it hasn't been moved in a while, consider using some WD-40 to loosen it up, or try pulling forward on the clip for additional leverage.
Once the metal part is removed, you will have access to the internal components of the stapler. You can now clear any jammed staples or perform other necessary maintenance. Remember to exercise caution, as some of the parts may be under tension or spring-loaded. After you have finished your repairs or cleared the jam, you can reassemble the stapler by reversing the steps. Ensure that all parts are securely locked into place, especially the follow block, to prevent any future issues.
If you are unable to remove the metal part or if there are other issues with your Swingline Strongarm 113 stapler, you can contact the manufacturer for further assistance or a potential replacement. It is important to follow the correct procedures to ensure the safety and proper functioning of your stapler.
Electric Pickup Trucks: Are They Here?
You may want to see also
Explore related products
How to load staples into a Swingline stapler: place staples legs-down in the tray, as close to the front end as possible
To load staples into a Swingline stapler, you must first open the stapler. Hold the base of the stapler with one hand, and with the other hand, pull out the staple tray. The tray is located at the stapler's back end, between the handles. It may take a little force to pull it out. Once the tray is out, you can begin loading the staples. Place the staples legs-down in the tray, ensuring they are as close to the front end as possible. The front end is the side closest to the inside of the stapler. Push any unused staples to the front to create more space. If you have a top-loading stapler, remember to remove the plastic sheath covering the staple tray. After loading the staples, push the tray back into the stapler. It should lock into place securely.
If your Swingline stapler has a follow block, you will need to push it in to loosen it before loading the staples. The follow block is a small metal latch that sticks out from the stapler's smooth edge, usually on the backside near the bottom. After loading the staples, slide the tray back into the stapler, and push the follow block in to lock the tray in place.
If your stapler is jammed, remove the old staples and any stuck pieces with pliers. Then, load the new staples as described above.
Android Dreams: Electric Sheep and Cluttered Minds
You may want to see also
Frequently asked questions
First, disconnect the power. Then, try to slide a putty knife or flat-bladed screwdriver under the front edge to lift it and get it back into position.
If your Swingline stapler is jammed, first dump out any old staples. Use pliers to pull out any staples that are stuck.
Always place staples legs-down in the tray, as close to the front end as possible. Push any unused staples to the front to create additional space.
After loading the staples, push the top of the stapler back down onto the tray. It should click into place.
The follow block is a small metal latch that sticks out from the stapler's smooth edge, usually on the backside near the bottom edge. It can be pulled upwards to release the hooks holding it in place and expose the staple tray.
