Umair Gaines
The Yashica Electro 35 is a rangefinder camera from the Yashica Electro series. If you're looking to open your Yashica Electro 35 camera, you may be attempting to clean the rangefinder, disassemble the front lens group, or address a locked film door. Online resources, such as YouTube videos and Flickr groups, provide guidance on disassembling and repairing the Yashica Electro 35, with some suggesting the use of tools like locking pliers and penetrating oil to aid in the process.
Explore related products
What You'll Learn
Removing the top cover
To remove the top cover of your Yashica Electro 35, you will need to proceed with caution. The top just lifts off, but it is attached by the flash sync wire, and the battery check button is also not attached to anything, so be careful as it may fall out.
First, you will need to remove the film rewind lever. Be careful not to close the film door once you've done this, or it will be difficult to open again. You will then need to remove the foam washer that keeps light from leaking in at the rewind lever.
Next, you will need to carefully detach the flash sync wire from the top cover. This will allow you to fully separate the top cover from the camera body. When putting the top cover back on, orient the camera so that the lens is up and slide the top onto the camera to keep the battery check button in place.
It is important to have a well-lit area to work in, and it is recommended to use a tray or paper towel to avoid losing any small parts. You may also need a jeweler's screwdriver to carefully detach the flash sync wire.
If you are having trouble removing the top cover, you can try applying a small amount of penetrating oil to the inner slotted retaining ring. Leave it for a while and repeat if necessary. This may help to loosen any corrosion or sticky residue that is holding the top cover in place.
MERV Rating's Impact: Energy Usage and Costs
You may want to see also
Explore related products
Disassembling the front lens
To disassemble the front lens of a Yashica Electro 35, you will need a well-lit workspace, a tray or paper towel, jeweller's screwdrivers, spanners, cotton swabs, and Windex. You may also need small-gauge wire, solder and a soldering iron, needle files, black felt or foam, vinegar, a lens brush, and tissues.
Start by removing the lens ring. Some lens rings are quite difficult to unscrew, but this can be facilitated by applying a small amount of oil to the inner, slotted retaining ring. Leave it for a long time and repeat if necessary. You can also use penetrating oil, which is designed to wick into metal threads. Alternatively, use a small flathead screwdriver to slot into the two small slots and spin the piece.
Next, unscrew the outer lens. You may need to use a screwdriver and a small hammer to tap it free. This will expose the shutter and multiple mounting screws. You only need to remove the inner three screws to take off the entire outer ring, which has the B/AUTO/Flash settings.
After removing the three inner screws, you are left with the aperture part of the lens. This is removed by unscrewing the centre ring around the shutter.
Understanding Electrical Device Power Draw Measurements
You may want to see also
Explore related products
Accessing the film door
To access the film door on your Yashica Electro 35, you'll need to locate and engage the film rewind knob. This knob is typically found on the left side of the camera, just above the lens. Begin by giving it a firm counter-clockwise turn. You'll feel some resistance, but keep turning until you hear a distinct click. This indicates that the film bayonet locking mechanism has been released.
With the locking mechanism disengaged, you can now safely open the film door. Gently lift the edge of the door closest to the lens and swing it outward, away from the camera body. The door should open easily, but be careful not to force it, as this could damage the hinge mechanism. As the door opens, you'll notice that it is connected to the camera body by a flexible black ribbon, which is the film compartment seal. This seal ensures light-tight performance when the film door is closed, so take care not to crease or damage it.
Once the film door is open, you'll have full access to the film compartment. Here, you can insert or remove film cartridges and tend to any internal maintenance or cleaning that may be required. It's important to work in a dust-free environment to avoid contaminating the film or camera mechanisms. When you're finished working inside the film compartment, it's time to close the film door.
To securely close the film door, first ensure that the film is wound onto the take-up spool correctly and that the film leader is securely attached to the spool. Then, carefully align the film door with the camera body, making sure that the film compartment seal sits flat and is not pinched or twisted. Gently lower the film door back into place, pressing around the edges to ensure a tight seal. Finally, give the film rewind knob another firm turn in the counter-clockwise direction to re-engage the bayonet locking mechanism. With the film door securely closed and locked, your Yashica Electro 35 is ready for shooting!
Living Off-Grid: Generating Self-Sufficient Electricity
You may want to see also
Explore related products
Cleaning the rangefinder
To clean the rangefinder of a Yashica Electro 35, you will need to disassemble certain parts of the camera. First, remove the three silver crosspoint screws from the top of the camera body—two on the sides and one on the back under the battery check button. Then, use a point spanner to remove the winder by turning the top counterclockwise. There may be washers and other small parts underneath, so be sure to keep them in a safe place, maintaining their original orientation.
Next, remove the ASA dial. First, set the ASA to 100, then use a point spanner to remove the center screw. The dial can then be lifted off. Now you will be able to access the rangefinder glass. Carefully lift off the rangefinder glass cover; it may be glued down or sealed with a large sticker, so take care.
Once the glass cover is removed, use a cotton swab moistened with Windex or a similar product to clean the inside of both viewfinders. Dry them with the other end of the swab. You can also clean the yellow glass, but be aware that doing so may remove the yellow tint and render your rangefinder useless.
Finally, reassemble the camera in the reverse order, replacing the foam washer at the rewind lever to prevent light leakage.
Artificial Lighting: Threatening the Sea Turtle Survival
You may want to see also
Explore related products
Using locking pliers
To open a Yashica Electro 35 using locking pliers, you will need a pair of locking pliers and a thin piece of rubber. The rubber is important as it will help you grip the metal part without damaging it.
Firstly, take your locking pliers and adjust the screw until the jaws are clamped shut without being locked. This will give you more control over the amount of force you apply. Next, place the thin rubber between the jaws of the pliers and the metal part of the camera you wish to grip. This will protect the metal from being damaged or destroyed. Now, carefully grip the metal part with the pliers and rubber, and gently apply force until the camera opens.
It is important to note that this method may not be suitable for all Yashica Electro 35 cameras, as there may be variations in the design or construction of different models. It is also important to exercise caution when using any tool to open a camera, as improper techniques can cause damage to the device.
Electric Spin Index Grinding Fixture: All You Need to Know
You may want to see also
Frequently asked questions
You can find a copy of the owner's manual and a Yashica Electro 35 shop repair manual at www.provins.org.uk.
Apply a small amount of oil to the inner, slotted retaining ring. Leave it for a long time and repeat if necessary. You can also use penetrating oil, which is designed to "wick" into metal threads.
You can use locking pliers and a thin piece of rubber to grip and not destroy the metal part.
Yes, there is a video on YouTube called "How to easily open the front lens group of a Yashica electro 35/gt/gsn/cc/gtn/gx/gc."
