Umair Gaines
The Yashica Electro 35 is a popular camera for photography enthusiasts, but it can be prone to age-related problems. Common issues include a stuck film advance lever, a dim rangefinder, and a locked film door. To open the film door, you must first open the back of the camera and then use a screwdriver or tweezers to turn the rewind lever counterclockwise. It is also important to note that if you close the film door after removing the rewind lever, it will be difficult to open again. In addition to this, the top of the camera can be removed by lifting it off, but caution must be taken due to the attached flash sync wire and loose battery check button.
Explore related products
What You'll Learn
Remove the film rewind knob
To remove the film rewind knob from a Yashica Electro 35 camera, follow these steps:
Firstly, locate the small, recessed film rewind button on the underside of the camera. Depress this button and ensure it stays down. This button can be found on the bottom of the camera, and it may be slightly recessed, so feel around for a small button.
Next, you will need to flip up the small handle on top of the film rewind knob. This handle is located on the top left of the camera body. Once you have flipped up this handle, you can begin to rotate it in the direction of the arrow painted on the rewind knob. It is important to turn the handle slowly to avoid discharging static electricity onto your film.
As you turn the handle, the film will begin to rewind. Continue turning until you feel a slight resistance. At this point, the film should be fully rewound, and you can now remove the film rewind knob by pulling it out. The back cover of the camera will pop open, and you can then remove the film cassette.
If the rewind knob is stuck, there are a few things you can try. Firstly, check that the shutter lock is in the unlocked position. If it is locked, unlock it and try again. You can also try gently turning the film advance sprocket and pushing down the shutter release. If that doesn't work, try giving the camera a light rap on the bottom plate with the heel of your hand while turning the sprocket and advancing with the thumb lever. Keep trying these steps for a while, and if all else fails, you may need to remove the bottom plate of the camera to investigate further.
Air vs Electric Tools: Which Offers More Power?
You may want to see also
Explore related products
Open the back cover
To open the back cover of the Yashica Electro 35, you must first ensure that the film has been rewound into its cassette. This is done by pressing the Film Rewind Release Button on the bottom plate of the camera. If you do not do this, you may tear the film perforations or damage the camera mechanism.
Next, unfold the crank handle on the Film Rewind Knob and slowly turn it in the direction of the arrow until you feel slight resistance. Continue slowly winding until you feel it turning freely. Then, gently let the rewind handle turn as the film may unwind itself within the cassette. If the film turns too quickly, static marks will fog and ruin your negatives.
Once this is done, you can open the back cover and remove the cassette. Be careful not to close the film door once you've removed the rewind lever, or it will be difficult to open again. The top just lifts off, but be aware that it is attached by the flash sync wire, and the battery check button is not attached to anything, so it may fall out.
Electric Toothbrushes: Spin or Vibrate?
You may want to see also
Explore related products
Insert the film
To insert film into your Yashica Electro 35, follow these steps:
First, pull out the Film Rewind Knob. This will cause the Back Cover to pop open, and the Film Exposure Counter will automatically be set to "S" (Start). Now you can open the back of the camera. Be careful not to close the film door once you've removed the rewind lever, or it will be difficult to open again.
Next, place a 35mm film cassette into the film chamber and push down the Film Rewind Knob. Then, insert the film leader into the Take-up Spool. You can now advance the film with the Film Advance Lever, ensuring that the perforations properly engage the sprocket teeth. Once this is done, close the Back Cover.
In the next step, gently wind the film rewind crank-handle on the Film Rewind Knob clockwise until you feel a slight resistance. Then, advance the film and press the shutter release button until the figure "1" appears in the Film Exposure Counter. Ensure that as you advance the film, the Film Rewind Knob rotates counter-clockwise.
Finally, align the mark on the ASA Film Speed Setting Ring with the ASA rating of the film you are using. You can find the Film rating on the box or the instructions that come with the film.
Lights and Electricity: Costly Combo or Efficient Energy?
You may want to see also
Explore related products
Wind the film
To wind the film on a Yashica Electro 35 camera, follow these steps:
Firstly, pull out the Film Rewind Knob. This will cause the Back Cover to pop open, and the Film Exposure Counter will automatically be set to "S" (Start). At this point, you can place a 35mm film cassette into the film chamber and push down the Film Rewind Knob.
Next, insert the film leader into the Take-up Spool and advance the film with the Film Advance Lever, ensuring that the perforations properly engage the sprocket teeth. Close the Back Cover.
Now, gently wind the film rewind crank-handle on the Film Rewind Knob in a clockwise direction until you feel a slight resistance. Advance the film and then press the shutter release button. Repeat this process until the figure "1" appears in the Film Exposure Counter.
Finally, make sure the film is properly loaded. As you advance the film, the Film Rewind Knob should rotate counter-clockwise.
Note that if you encounter any issues with a stuck film advance lever, as some users have reported, you may need to open the camera and check for any obstructions or debris. Always exercise caution when opening your camera and refer to detailed repair guides or manuals if necessary.
Electrical Repairers: Where Are They Based?
You may want to see also
Explore related products
Check for proper loading
Loading film into your Yashica Electro 35 is a simple process, but it's important to ensure that it's done correctly to avoid any issues with your camera or film. Here's a detailed guide to help you check for proper loading:
Check the Film Exposure Counter
The Film Exposure Counter should be automatically set to "S" (Start) when you first load your film. This is an important indicator to ensure your film is properly loaded and ready for shooting.
Verify Film Cassette Placement
Place a 35mm film cassette into the film chamber and push down the Film Rewind Knob. Ensure that the cassette is securely in place and doesn't move around. This is crucial for maintaining the proper tension on your film.
Insert Film Leader
Carefully insert the film leader into the Take-up Spool. This step is crucial for ensuring smooth film advancement. Make sure the perforations on the film leader properly engage the sprocket teeth. Any misalignment can lead to film jams or uneven advancement.
Advance the Film
Use the Film Advance Lever to advance the film. As you do this, the Film Rewind Knob should rotate counter-clockwise. This indicates that the film is properly engaging the rewinding mechanism. Continue advancing until you feel slight resistance.
Check Film Rewind Function
Gently wind the film rewind crank-handle on the Film Rewind Knob in a clockwise direction until you feel a slight resistance. This step ensures that the film is properly aligned and can be rewound smoothly without tangles or jams.
Confirm Film Advance and Exposure Counter
Advance the film again and press the shutter release button. Repeat this step until the figure "1" appears in the Film Exposure Counter. This confirms that the film is advancing correctly and the counter is functioning as intended.
Align Film Speed Settings
Finally, align the mark on the ASA Film Speed Setting Ring with the ASA rating of your film. You can find this rating on the box or instructions that come with your film. This step ensures that the camera is set up correctly for the specific film you are using.
By following these steps, you can be confident that your film is properly loaded in your Yashica Electro 35. Remember to always handle your film and camera with care to avoid any damage or mishaps during the loading process.
Ceiling Fan Speed: Electricity Consumption's Worst Enemy?
You may want to see also
Frequently asked questions
To open the back cover of your Yashica Electro 35, first pull out the Film Rewind Knob. The back cover will then pop open.
To remove the rewind knob, open the back cover and use a screwdriver or tweezers to turn the rewind lever counterclockwise.
First, remove the three silver crosspoint screws from the top of the camera. Two screws are on the sides, and one is at the back under the battery check button. Then, use a point spanner to remove the winder by turning the top counterclockwise.
