Wiktor Wise
Sunbeam manufactures heated bedding products, including electric blankets and mattress pads, that can be controlled via a digital control or through the Sunbeam App. To turn on a Sunbeam electric blanket, you can press the On/Off button on the control unit or plug the main power cord into a 110-volt or 120-volt wall outlet. It is important to note that Sunbeam products should not be dried using commercial dryers, as they can damage the wiring. Additionally, do not dry clean, bleach, iron, or submerge the product in water as it may pose a fire hazard.
Explore related products
What You'll Learn
Plug the blanket into a wall outlet
To plug in and turn on your Sunbeam electric blanket, follow these steps:
Firstly, ensure that your blanket is laid out flat. If you have already used your blanket, fold it as you would normally store it. Make sure to keep it folded throughout the process. Locate the control or controls in the centre of the fold and slip them out. Check that the control cord is connected to the connection module. If not, simply plug it in by clicking the plastic clasps into place.
Next, plug the main power cord into a wall outlet. It is important to note that Sunbeam recommends using a 110-volt or 120-volt wall outlet. Do not use an extension cord or power adapter; plug the heated blanket directly into the wall outlet. Once plugged in, press the "On/Off" or "On" button to turn on your blanket.
You can adjust the temperature of the blanket by turning the large dial on the control unit. The temperature selected will be displayed on the small screen. If you wish to preheat the blanket, press the "On/Off" button once and then the "Preheat" button. The blanket will warm up for 30 minutes before returning to its previous setting.
Remember, Sunbeam electric blankets are designed to provide lightweight warmth, so they will not feel hot to the touch when laid out flat. If you have followed these steps and your blanket is not heating up properly, stop using it immediately and contact Sunbeam support.
Electric Furnace Elements: How Many Do You Need?
You may want to see also
Explore related products
Turn the dial on the control unit
To turn on your Sunbeam electric blanket, you must first locate the control unit. This is usually found in the centre of the blanket, especially if you have already folded it for storage. The control unit will have a large dial on top, which is used to adjust the temperature.
Turning this dial will allow you to select your desired temperature, which will be displayed on the small screen of the control unit. You can also preheat your blanket by pressing the "On/Off" button and then the "Preheat" button. The blanket will warm up for 30 minutes and then return to its previous setting.
If your Sunbeam blanket has dual controls, the control with the label on the bottom operates the side of the product with the matching label. You can also use the Sunbeam App to create and modify schedules for your blanket. However, scheduling cannot be set up with voice commands.
It's important to note that Sunbeam heated bedding will not feel hot to the touch when laid out flat. If you feel your blanket is not heating properly, ensure that the control cord is connected to the connection module. Plug the main power cord into a wall outlet and turn the control to the highest setting for 20 minutes. If the blanket still does not perform properly, stop using it and contact Sunbeam support.
Jaguar's Electric Future: All-In by 2025?
You may want to see also
Explore related products
Reset the blanket
If your Sunbeam electric blanket is not functioning properly, you may need to reset it. To verify whether your blanket is heating properly, perform the fold test. First, fold your blanket as if you were about to store it away. Then, locate the controls without unfolding the blanket and check that the control cord is properly connected to the connection module. Plug the power cord into an electrical outlet, turn the blanket "on", and set it to the highest setting. Wait for a few minutes (never more than 7), then place your hand between the folds to check if the blanket is heating. If not, you may want to try resetting it.
To reset your Sunbeam electric blanket, follow these steps: First, unplug the blanket from the outlet. Second, check that the control is properly connected to the module in the blanket. Re-plug the power cord into the wall outlet. On a digital control, you should see flashing symbols and the display on your control will clear. Your blanket is now reset.
If your blanket has a digital display, it will flash with the "FF" sign if your product has encountered a problem. With products that have gradient controls, this will be indicated by blinking. If you see this, it is time to reset your blanket.
To reset, simply unplug the power cord from the wall outlet for at least 30 seconds. Then, unplug the connector from the blanket/mattress pad. Wait 20 minutes, then plug the connector back into the pad. Wait a few minutes and plug the power cord back into the wall outlet.
If the issue persists, contact Sunbeam's customer support.
Electricity Rates: Winter's Impact and Cost-saving Strategies
You may want to see also
Explore related products
Use the pre-heat function
The pre-heat function on your Sunbeam electric blanket is a useful feature that can make your experience even more convenient and comfortable. Here's how you can use it:
Locate the Control Unit: The first step to accessing the pre-heat function is to locate the control unit of your Sunbeam electric blanket. This unit should have a temperature dial and a small screen for displaying the selected temperature. It will also have buttons, including an “On/Off” button and a “Preheat” button.
Turn on the Blanket: Before using the pre-heat function, ensure that your electric blanket is turned on. Press the "On/Off" button once to power up the blanket. The display on the control unit should illuminate, indicating that the blanket is ready for use.
Activate the Pre-Heat Function: With the blanket turned on, you can now activate the pre-heat function. Press the "Preheat" button, which is usually located near the "On/Off" button. This initiates a 30-minute pre-heat cycle, during which the blanket will warm up to the highest setting. This is a convenient way to quickly heat up your bed before settling in for the night.
Automatic Return to Previous Setting: After the 30-minute pre-heat cycle is complete, the electric blanket will automatically return to its previous heat setting. This is a useful feature that ensures your blanket doesn't remain at the highest temperature, providing you with a comfortable and customizable experience. You can always adjust the temperature to your preference using the dial on the control unit.
Compatibility with Voice Assistants: If you use voice assistants like Alexa, keep in mind that it can interact with your Sunbeam electric blanket. However, Alexa will not increase the temperature beyond level 10 (H) during the pre-heat cycle, as this function is set to the highest setting by default. You can still use Alexa to adjust the temperature within the given range after the pre-heat cycle is complete.
Dispose of Your Braun Electric Toothbrush the Right Way
You may want to see also
Explore related products
Adjust the timer settings
Adjusting the timer settings on your Sunbeam electric blanket is simple. The heated blanket includes an automatic 10-hour auto-off, and it will turn off after 10 hours of use. You can change this setting by opening the Sunbeam app and pressing the timer icon. The timer can be set for up to 10 hours in 0.5-hour increments. If you would like to keep the blanket on for longer, select the "Stay On" option to keep the heated bedding on for 24 hours. Unfortunately, you cannot set a timer for your heated blanket with voice control.
If you have the Pre-Heat function on, the blanket will return to the heat setting of the schedule after the pre-heat cycle (30 minutes) is complete. To preheat the blanket, press the "On/Off" button once and then hit the "Preheat" button.
Please note that Alexa will not allow you to increase the temperature during pre-heating as the pre-heat function is set to the highest setting.
Electric and Magnetic Forces: What's the Core Difference?
You may want to see also
Frequently asked questions
First, remove the blanket from its vinyl storage bag. Then, plug the main power cord into a 110-volt or 120-volt wall outlet. Finally, press the "On/Off" or "On" button to turn on the blanket.
Adjust the temperature by turning the large dial on the top of the control unit. As you turn the dial, the temperature selected will be displayed on the small screen on the control unit.
Press the "On/Off" button once and then press the "Preheat" button. The blanket will warm for 30 minutes before returning to its previous setting.
The heated blanket includes an automatic 10-hour auto-off feature. In the app, you can change this setting by pressing the timer icon and setting the timer for up to 10 hours in 0.5-hour increments or choosing "Stay On" for 24 hours.
